由于钢筋加工棚的施工质量会对后期使用的产生较大影响，因此，在搭设钢筋加工棚的过程中应注意以下施工要点。

Due to the significant impact of the construction quality of the steel bar processing shed on the safety of later use, the following construction points should be noted during the installation of the steel bar processing shed.

工地钢筋加工棚_工地钢筋防护棚_标准化制作解析

Construction site reinforcement processing shed_ Construction site steel reinforcement protection shed_ Analysis of standardized production

（1）施工前，应先编制详细的防护棚施工方案，并在开始施工时先对防护棚范围内的两侧道路进行整平、拓宽作业，设置排水沟，以确保排水畅通，适应吊车站位及吊装。

(1) Before construction, a detailed construction plan for the protective shed should be prepared, and before starting construction, the roads on both sides of the protective shed should be leveled and widened, and drainage ditches should be set up to ensure smooth drainage and adapt to the crane position and lifting.

（2）若钢筋加工棚的基础施工范围内光缆、电力线众多，还应制订光缆、电力线等设备的改移方案，以及相关保护措施，以确保施工和设备。

(2) If there are many optical cables and power lines within the basic construction scope of the steel bar processing shed, a relocation plan for equipment such as optical cables and power lines should also be formulated, as well as relevant protective measures, to ensure construction safety and equipment safety.

（3）钢筋加工棚施工时，其焊接作业的过程一定要注意防火，如果有风必须设置好挡风板，以免发生火花飞溅，造成隐患。同时，钢筋加工棚上不得堆放杂物，以及钢筋、模板等材料，以防发生火灾。

(3) During the construction of the steel bar processing shed, attention must be paid to fire prevention during the welding process. If there is wind, a wind deflector must be installed to avoid sparks and potential safety hazards. At the same time, debris, as well as materials such as steel bars and templates, should not be piled up on the steel bar processing shed to prevent a fire.

（4）按钢筋加工棚的矩型管立杆间距、排距要求进行定位放线，并将垫板铺设放平稳，不得悬空。同时，矩型管立杆接长应采用对接电焊连接，立杆对接电焊焊接应交错布置。

(4) Position and set out according to the spacing and row spacing requirements of the rectangular pipe upright in the steel processing shed, and lay the base plate smoothly without hanging in the air. At the same time, the extension of the rectangular pipe upright should be connected by butt welding, and the butt welding of the upright should be arranged in a staggered manner.

工地钢筋加工棚_工地钢筋防护棚_标准化制作解析

Construction site reinforcement processing shed_ Construction site steel reinforcement protection shed_ Analysis of standardized production

（5）钢筋加工棚棚顶铺装施工时，均应在既有线上方作业，且须注意高空作业，严禁任何机具和材料意外掉落损坏线路设备。同时，应通过钢管立柱，在钢筋加工棚两侧设置接地措施。

(5) When paving the roof of the steel processing shed, operations should be carried out above the existing line, and attention should be paid to the safety of high-altitude operations. It is strictly prohibited for any machinery and materials to accidentally fall and damage the line equipment. At the same time, grounding measures should be set up on both sides of the steel processing shed through steel pipe columns.

现场钢筋加工棚一般需根据施工织计划，安置钢筋对焊机、切断机、弯曲机、调直机......等设备的数量及加工流水线；另还需考虑部分钢筋原材料、加工后钢筋的周转及堆放；现场施工场地、用电等条件来确定；故钢筋加工棚一般跨度在12~18m,，长度尽可能大于30m。

The on-site steel bar processing shed generally needs to be equipped with steel bar welding machines, cutting machines, bending machines, straightening machines, etc. according to the construction weaving plan The number of equipment and processing lines; In addition, it is necessary to consider the turnover and stacking of some raw materials and processed steel bars; Determine the construction site and electricity usage conditions on site; Therefore, the steel bar processing shed generally has a span of 12-18 meters, and the length should be as much as possible greater than 30 meters.

工具式钢筋加工棚搭设具体尺寸根据现场实际情况确定。

The specific dimensions for setting up a tool type steel bar processing shed will be determined based on the actual situation on site.

搭设在塔吊回转半径和建筑物周边的加工车间必须设置双层硬质防护。

The processing workshop set up around the turning radius of the tower crane and the building must be equipped with double layer hard protection.

加工车间地面需硬化，宜选用砼地面。

The ground of the processing workshop needs to be hardened, and concrete ground should be selected.

加工车间顶部应张挂警示标识和宣传用语的横幅，横幅宽度宜为1m。

Safety warning signs and safety propaganda slogans should be hung on the top of the processing workshop, with a width of 1m.

工具式钢筋加工棚需在醒目处挂操作规程图牌，图牌的尺寸为：宽×高=2000mm×1000mm。

The tool type steel bar processing shed needs to be prominently hung with an operating procedure diagram board, with a size of: wide × Height=2000mm × 1000mm。

各种型材及构配件规格为参考值，具体规格应根据当地风荷载、雪荷载进行核算。

The specifications of various profiles and components are reference values, and the specific specifications should be calculated based on local wind and snow loads.

南方地区，如遇台风应采取防风措施，可设置缆风绳。

In the southern region, if encountering a typhoon, wind prevention measures should be taken and cable ropes can be installed.