木工加工棚的作用

Function of woodworking shed

木工加工棚是在木工加工场地、钢筋加工场地等上方有可能坠落物件或处于起重机调杆回转范围之内，应搭设双层防护棚。木工加工棚的作用及部件使用案例是怎样的？

The woodworking shed is a double-layer protective shed that may fall objects above the woodworking site and reinforcement processing site or is within the rotation range of the crane adjusting rod. What is the function of woodworking shed and the use case of components?

木工加工棚就是施工现场保护施工人员，用钢管作为支撑骨架，上面覆盖竹串片或者竹笆板或者废模板作为防砸，或者保护防护棚内经过的诸如高压线之类的东西。一般的双层防护是为了加大系数。

The woodworking shed is used to protect the construction personnel at the construction site, with steel pipes as the support framework, covered with bamboo strips or bamboo fence boards or waste formwork as anti smashing, or to protect the high-voltage lines passing through the protective shed. The general double-layer protection is to increase the safety factor.

木工加工棚长和宽尺寸，要根据钢筋加工数量和使用机械的多少确定加工棚的大小，一般情况有6*9m、6*12米、9*12m等几种，可以根据实际情况酌情采用，也可自行设计长宽尺寸。

The length and width of the woodworking shed shall be determined according to the number of reinforcement processing and the number of machines used. Generally, there are 6*9m, 6*12m, 9*12m and so on, which can be adopted according to the actual situation or designed by ourselves.

钢筋加工棚案例：

Reinforcement processing shed case:

立柱：采用150mmX150mmX3mm方钢管，中心距4.15m，立柱焊接在地面预埋钢板上，立柱高3.2m，加强棚方钢管喷涂双色油漆，底漆涂一次，面漆为黄色，两种黑色涂料，从底部刷黑色涂料，向上每隔50cm交替使用黄色和黑色涂料，共涂两次。

Column: 150mmx150mmx3mm square steel pipe with center distance of 4.15M is used. The column is welded on the embedded steel plate on the ground. The column is 3.2m high. The square steel pipe of the reinforced shed is sprayed with two-color paint. The primer is painted once, and the finishing coat is yellow. Two kinds of black paint are applied from the bottom. Yellow and black paint are applied alternately every 50cm upward, twice in total.

支架：水平使用40mmX60mmX3.5mm方钢管，跨度12m（两端悬挑1m），焊接在立柱上，支架与立柱斜撑之间用40mmX60mm方钢管连接，支架和屋脊采用40mmX60mmX3.5mm方钢管连接，支架底部油漆使用防锈漆一次，面漆使用铁红漆两次。

Support: 40mmx60mmx3.5mm square steel pipe is used horizontally with a span of 12m (both ends are cantilevered for 1m), which is welded on the column. 40mmx60mm square steel pipe is used to connect the support and the column diagonal brace. 40mmx60mmx3.5mm square steel pipe is used to connect the support and the roof ridge. Antirust paint is used at the bottom of the support once, and iron red paint is used for the finish twice.

脊柱：水平方向采用40mmX60mmX3.5mm方钢管，与立柱、支架焊接，两端悬臂，悬臂长度20cm。纵向采用C型钢50mmX80mm，共涂11道，油漆两道，底漆一道防锈漆，面漆两道铁红漆。

Spine: 40mmx60mmx3.5mm square steel pipe is used in the horizontal direction, welded with the column and support, cantilever at both ends, and the cantilever length is 20cm. C-shaped steel 50mmx80mm is applied longitudinally, with 11 coats of paint, two coats of antirust paint for primer and two coats of iron red paint for finish.

屋面：屋面用蓝色钢板覆盖（包括悬挑部分），用铆钉将彩钢板与脊骨固定牢固，相邻彩钢板搭接5cm，彩钢板铺设在屋脊梁水平方向，各钢筋加工棚一端采用彩钢板。覆盖，两个移动钢筋加工大棚对接的上下位置错开，一个移动钢筋加工大棚的彩钢板末端悬垂10cm。

Roof: the roof is covered with blue steel plate (including the cantilever part), the color steel plate and spine are fixed firmly with rivets, the adjacent color steel plates are overlapped by 5cm, the color steel plate is laid in the horizontal direction of the ridge beam, and the color steel plate is used at one end of each reinforcement processing shed. Covering, the upper and lower positions of two mobile reinforcement processing sheds are staggered, and the end of the color steel plate of one mobile reinforcement processing shed is suspended for 10cm.

标牌位置：面向基坑方向设置标牌，从立柱顶部开始，纵向采用40mmX60mmX3.5mm方钢管，2行，中心间距94cm，纵向铺设两根钢管-1m宽和0.20mm宽厚薄铁皮、方钢管和立柱焊接固定。

Location of signs: signs shall be set facing the foundation pit. Starting from the top of the column, 40mmx60mmx3.5mm square steel pipes shall be used longitudinally in two rows with a center spacing of 94cm. Two steel pipes -1m wide and 0.20mm wide thin iron sheets shall be laid longitudinally, and the square steel pipes shall be welded and fixed with the column.

木工加工棚的作用及部件使用案例相关内容就是这样了，如果您有需求选购就来关注我们网站www.jnpfjc.com，为您准备各种型号的加工棚或者围栏。

This is the function of the woodworking shed and the relevant content of the component use cases. If you need to purchase, please follow our website www.jnpfjc Com to prepare various types of processing sheds or fences for you.